Texas-instruments TUSB3210 Manual do Utilizador

TUSB3210 GenericEvaluation Board2005 MSP USBUser’s GuideSLLU031A

Running Title—Attribute Reference1-2 1.1 EquipmentFigure 1−1. TUSB3210 Evaluation EquipmentUSB EVM1.2 Hardware OverviewThe TUSB3210 EVM hardware plat

Running Title—Attribute Reference1-3 Chapter Title—Attribute ReferenceTUSB3210 device. A USB cable should be plugged into a USB port on a PCor into a

Running Title—Attribute Reference1-4 Figure 1−4. TUSB3210 Printed-Circuit Board (REV 1.1)—Top Side

Running Title—Attribute Reference1-5 Chapter Title—Attribute ReferenceFigure 1−5. TUSB3210 Printed-Circuit Board (REV 1.2)—Top Side

Running Title—Attribute Reference1-6 1.3 Bill of MaterialsItem Quantity Reference Part1 3 (REV 1.1 board) C1, C4, C10 Capacitor, 0.1 µF1 7 (REV 1.2 b

Running Title—Attribute Reference1-7 Chapter Title—Attribute Reference1.4 Schematic DiagramThe complete schematic diagram of the TUSB3210 generic EVM

1-8

2-1 Chapter Title—Attribute Reference EVM OperationThis chapter describes the operation of the TUSB3210 EVM.Topic Page2.1 TUSB3210 Setup 2-2. . . . .

Running Title—Attribute Reference2-2 2.1 TUSB3210 SetupThe TUSB3210 EVM supports many USB applications. The jumpers allow theflexibility to configure

Running Title—Attribute Reference2-3 Chapter Title—Attribute Reference2.5 Jumpers and SwitchesTable 2−2 is provided to help set up and configure the

IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,enhancements, improvemen

Running Title—Attribute Reference2-4 Figure 2−1. GPIO Connector135791113151719212325272931333537394143454749P0.0P0.2P0.4P0.6P1.0P1.2P1.4P1.6P2.0P2.2P

AABBCCDDEE4 43 32 21 1[Wait 10ms before enable 3.3V][If S2 or S3 tied to ground, remove100K pull-up to save power]base1.dsnBEC123B31E2CNPNMMBT4401MMBT

AABBCCDDEE4 43 32 21 1[Wait 10ms before enable 3.3V][If S2 or S3 tied to ground,remove 100K pull-up to savepower]base1.dsnBEC123B31E2CNPNMMBT4401MMBT4

EVM IMPORTANT NOTICETexas Instruments (TI) provides the enclosed product(s) under the following conditions:This evaluation kit being sold by TI is int

EVM WARNINGS AND RESTRICTIONSIt is important to operate this EVM within the input voltage range of 4 V to 6 V and the outputvoltage range of 3 V to 3.

Related Documentation From Texas Instrumentsv PrefaceRead This FirstAbout This ManualThis user’s guide describes the setup and operation of the TUSB3

TrademarksviTrademarksMacOS is a trademark of Apple Computer, Inc.Windows and Windows ME are trademarks of Microsoft Corporation.Other trademarks are

Contentsvii Contents1 Hardware and Software Required 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

viii

1-1 Chapter Title—Attribute Reference Hardware and Software RequiredThe TUSB3210 generic EVM is designed for use with a personal computerrunning a USB