Texas Instruments CC2533 Manual do Utilizador

CC2533 RF4CE BasicDevelopment KitHardware User’s GuideSWRU266

swru26610/25The latest version of RemoTI software can be downloaded from the Texas Instrumentswebsite (http://www.ti.com/remoti), where you will also

swru26611/25Figure 4: Connecting the target module for the first time (Windows XP)Select “No, not this time” and continue with “Next”.Figure 5: Select

swru26612/25Figure 6: The driver installation is completed (Windows XP)Select the following directory <Installation Path>\Tools\Driver for the n

swru26613/254.7 Testing the Remote Control applicationYou are now ready to use the development kit to test remote control. The RemoTI softwarepackage

swru26614/255 Programming and Debugging5.1 Using the SmartRF Flash Programmer PC softwareThe SmartRF Flash programmer PC software is used for programm

swru26615/25Figure 9: Connecting the remote control to the CC DebuggerCare should be taken when connecting the CC Debugger cable to the remote control

swru26616/25Figure 10: Connecting the target module to the CC Debugger

swru26617/256 The Target ModuleThe target module is designed to allow flexible interfaces for many common types ofinterfaces used in typical remote co

swru26618/256.1.2 USBThe USB port is used for powering the board and for serial interface to the CC2533. ATUSB3410 is used to translate the serial por

swru26619/25UART CTS(P1.3) 5 6 UART RTS(P2.18)SPI CSN(P1.14) 7 8 SCLK(P1.16)MOSI(P1.18) 9 10 MISO(P1.20)I2C SDA(P1.11) 11 12 I2C SCL(P1.5)EM_RESET((P2

swru2662/25Table of Contents1 INTRODUCTION...

swru26620/25The IR receiver is a Vishay TSOP85238. The receiver is optimized for 38 KHz input signal.The IR input is connected to the IR_IN signalThe

swru26621/257 Appendix A: Opening the remote controlYes, we know you will do it… Here are the instructions how to open the remote controlwithout break

swru26622/258 Appendix B: How to upgrade the target module USB driverThe target module USB driver information is stored an EEPROM for the TUSB3410 USB

swru26623/25Figure 18: Using the EEPROM burner softwareAfter successful programming, unplug the mini-USB cable, mount the CC2533EM on thetarget module

swru26624/259 Schematic and LayoutThe complete design files including schematic and layout for the remote control, targetmodule, and EM module can be

swru26625/2510 Document HistoryRevision Date Description/Changes- 2010-08-16 First revision.

IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improveme

swru2663/25List of FiguresFigure 1: Remote Control Key layout ... 8F

swru2664/251 IntroductionThe CC2533 RF4CE Basic development kit (part # CC2533DK-RF4CE-BA) allows you toevaluate RF4CE remote controls and develop app

swru2665/253 Acronyms and AbbreviationsDK Development KitEM Evaluation ModuleI2C Inter-Integrated Circuit (communication bus)IC Integrated CircuitIR I

swru2666/254 Getting Started4.1 Development Kit ContentThe development kit includes the following main components:RF remote controlA complete cost opt

swru2667/25USB dongleThe USB dongle can be programmed toreplace the functions of the Target Module. Itsupports virtual serial port interface and HID(H

swru2668/25for instructions to run the PER and latency test, and the RemoTI Latency and PacketError Rate Application Note (SWRA262) for sample measure

swru2669/25Figure 2: Target module layoutFigure 2 shows the key layout of the target module with some of the peripheral interfaceshighlighted. For det